Pereiti prie produkto informacijos
1 apie 2

Atskiros juostelės 2003 m. Ford F-150 pilkai / juodai Harley-Davidson

Atskiros juostelės 2003 m. Ford F-150 pilkai / juodai Harley-Davidson

SKU:501-1

Reguliari kaina €21,97 EUR
Reguliari kaina Pardavimo kaina €21,97 EUR
Išpardavimas Sold out
Mokesčiai įskaičiuoti. Siuntimas skaičiuojamas atsiskaitant.

Mažai atsargų: liko 5

Korpuso skydelis

Vinilo lipdukai, skirti 2003 metų modelio Ford F-150 Harley-Davidson 100-mečio leidimo sunkvežimio restauravimui. Tik dviejų spalvų (juodos ir pilkos spalvos) sunkvežimiui. Čia galite pasirinkti tik vieną vinilinę juostelę tik vienos sunkvežimio plokštės dažymui

Tinka šiems modeliams: F-150

Papildoma informacija

These are replicas of the original stripes, printed with all original details and precisely cut to the original shape. Stripes are shaped for easier application, and no hard bending is needed as if they were straight cut. Decals are manufactured of top-quality Oracal vinyl film and look extremely accurate and similar to OEM stripes.

These decals are covered with a very thin, tough, clear coat to resist all weather conditions and last for years. This exclusive technology enables the application of decals after finishing a complete paint job.

There is no need to cover these decals with a layer of clear lacquer.

Application of these decals is simple, and you need no special tools or skills to complete the job.

We respect Copyright Laws and produce decals with slightly altered original lettering. Please remember that these alterations are unnoticeable, and the decals look like they were originally made that way.

Ford Decals Application Instruction

The following are general instructions for applying STICKERHAUZ laminated stickers and decals to motorcycles, their parts, and other vehicles. This instruction covers the application of printed vinyl decals and die-cut stickers as well.

Storage

STICKERHAUZ decals must always be stored in cool, dry places away from the sun. Before application, the films should be adapted to required moisture and temperature conditions: an indoor climate of 40% to 50% relative humidity and a temperature of +18° to +22°C (+65°F to +72°F) is ideal. If the above-mentioned conditions are radically altered, dimensional changes of the protective paper may result. A consequence would be inadequate flatness of the self-adhesive material and dimensional deviations of the pieces. All stickers that come rolled in the box should be laid on a flat surface at least for 24 hours before being applied.

Procedure

Prosecute the application process in dust, wind, and no direct sun-controlled area or room. The environmental temperature should be +18°C (65°F) or above to achieve the required bond strength. Any dust particles, trapped under stickers, will form visible, small air bubbles.

Thoroughly clean the surfaces of the vehicle before applying the STICKERHAUZ vinyl decals. Provide general vehicle cleaning with conventional cleaning agents. Clean bonded surfaces additionally with IPA isopropyl alcohol (isopropanol). This will remove most efficiently all residues of previously used cleaning agents, wax and debris from painted areas. Thoroughly dry surfaces, use a hot air blower to remove any residual moisture.

Note:

Solvent residues owing to improper cleaning or a recent paint job may result in gas bubbles forming between the film and the base. Make sure that stickers are only bonded to completely dry and hardened coating finishes. As a rule of thumb, allow a minimum drying period of three weeks.

Film application procedure

In general, STICKERHAUZ laminated vinyl decals you shall process like common polymeric car wrapping PVC films. If you are not sure about your experience to correctly applying decals, please refer to your local window tint shop for installation assistance.

We recommend dry bonding procedure as follows:

Prosecute the application process at the ambient temperature mentioned above. Avoid significant alteration in temperature during the first 24 hours after adhesion. Should a temperature drop nonetheless occur, we recommend treating the decals with hot air from a hot-air gun.

Lay the decals with the film side down on a flat surface. Pull back only as much silicone paper as required to begin mounting. Always draw the silicone paper from the film, never the other way round.

Position the piece of film to be bonded on the vehicle and secure it with adhesive tape or film scraps.

Make sure that film projects over the edges of the vehicle part to be bonded.

Remove the backing paper and evenly stretch the film over the vehicle part.

Press the film on to the vehicle with the squeegee in even, overlapping wiping movements.

Depending on the size of the cut to be mounted, the silicone paper may be removed completely before bonding or gradually during the adhering procedure.

When using application paper or film (some of our decals come with application film or paper already applied), pull these slowly away from the film at a 180° angle.

Different background profiles are used in vehicle construction. When applying films to such backgrounds always follow the profile. Never just lay out the film and press it under tension into the recess.

After completion of the work

The motorcycle or the part of it with freshly applied STICKERHAUZ decals should be kept at the bonding temperature for at least another 24 hours.  Only after about 3 days, the film will reach its ultimate bond strength.

These Processing Instructions are based on our knowledge and experience. They do not comprise explanations of every aspect to be considered during film bonding. Specific knowledge and skills of window tint technicians or bonding specialists may be brought. A guarantee of specific properties cannot be derived from this information.

Pristatymo informacija Peržiūrėkite visą informaciją

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
s
s3255s

thanks